6530A REV F Norge Washer Parts List

Flat style oven igniter

The flat-style oven igniter is used to ignite the gas to light the oven burner in your range. If your oven is not heating, check the igniter to make sure it is glowing. If the igniter is glowing and your oven is not heating, your igniter is not strong enough to heat the oven and you will need to replace it. When replacing the igniter, be very careful not to touch the black element part of the igniter as it is very fragile. The part measures approximately 3.72-inch in length and the amperage range is 3.2 to 3.6. This is a genuine OEM part.

Lower rack assembly - grey (rack assy)

This part is a genuine OEM part. This white lower dish rack assembly comes with eight light-gray rollers for easy access. The dish rack is approximately 21 inches wide x 22 inches deep. The dish rack holds dishes in place during the dish washing cycle. If you see rust spots on the dishes, the lower rack will not pull out, or the lower rack is visibly rusted or damaged, you will need to replace the part. Other common symptoms include: unusual or loud noises coming from the unit, or the dishes on the lower rack not being washed properly.

M series new style coil kit (dryer secondary valve coil)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Meat drawer rail - right side (drawer support rail - right side)

This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is broken or the drawer is not sliding properly, you will need to replace the slide rail. You will need a Phillips screwdriver to complete this repair.

Rear drum bearing kit (rear drum bearing assembly)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Bake element - 2600w 240v (elmnt-bake)

The 2600 watt 240 volts bake element is located inside the oven on the bottom to supply heat while baking. This closed hinged style bake element is 15 3/4-inch long 16 5/8-inch wide, terminal depth is 3-inch and they are 1 3/4 inches apart. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Upper crisper drawer cover - glass not included (upper crisper drawer cover)

This cover holds up the top crisper drawer, and has drawer glides molded in it. This upper crisper drawer cover is a manufacturer-approved replacement part for your refrigerator. It has drawer glides molded into the frame but this part does not include the glass cover. To replace this part, lift out the glass cover and snap out the drawer frame. Snap this new frame cover into place and replace the glass.

Refrigerator water filter (use wf2cb)

This is a single OEM water filter used in refrigerators to remove impurities and particles from water that goes through the water and ice dispenser. It is used for reducing cysts, turbidity, lead, mercury, herbicides, and more. If your icemaker is not making ice, not dispensing ice, dispenses too little ice, or there is leakage and the fridge is making loud noises, replacing the water filter may be the solution. This filter is located in the front, top right of side-by-side refrigerators. You will know it is time for a new filter when the light on the freezer door dispenser lights up red, or after 6 months (200 gallons) of use. No tools are required for this easy repair. First, press the release button to pull out the old water filter and push and lock in the new water filter. Run water through the dispenser for about 3 minutes to prime the filter for use. Dispose of the water or use it to water plants. Press the indicator for 3-10 seconds to reset after this repair is complete. This carbon-based filter measures 6 x 3 x 7 Inches and is white plastic. Note: You may also need to order the water filter base to make the water filter fit properly. Please use your model number to locate the filter base.

Door rack (rack-door)

This OEM door rack for your refrigerator is sold individually.

Water filter (use wfcb)

Manufacturer's Number: WFCB The PureSourcePlus filter fits refrigerators made before 2001, and Kenmore refrigerators with model numbers starting with 253. This filter has white ends, while the EAP503619 has blue ends. May require the EAP428513 wrench or EAP428532 O-ring. Filters for: Taste and odor Sediment 99.3% of Lead 99.99% of Cysts 99.7% of Turbidity 99.8% of Particulates (Class I) 94.9% of Atrazine (a herbicide) 94.2% of 2,4-D (a herbicide) 97.8% of Chlorine (Class I) 87.5% of Toxaphene (a pesticide)

Refrigerator door shelf bin (bin-door,pseudo,bottom)

Front drawer glide (drawer glide)

This front drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact and offer support for the drawer. If you are having trouble opening and closing the broiler drawer, the glide may be broken and will need to be replaced. Your range has 4 in total – 2 front and 2 rear. This is a genuine OEM part and is sold individually.

Door catch kit (dryer door latch kit)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Drive belt (belt drive)

This dryer drum drive belt is 89.5" long and has four ribs. This part helps spin the drum during the drying cycle.

Lower spray arm (use 154414101)